Yokogawa 2-Wire Dual Channel Transmitter/Analyzer FLXA21 Manual de usuario Pagina 162
- Pagina / 246
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
<13. COMMISSIONING OF DO (Dissolved Oxygen)>
13-11
IM 12A01A02-01E 5th Edition : Oct. 31, 2013-00
If blank is selected for a parameter, items below that parameter must all be set to blank. If an item
is blank, those below it cannot be set to a status other than blank.
For more information on HART communication, see the Technical Information (TI 12A01A02-
60E)intheattachedCD-ROM.
n PH201G
Select this menu if the PH201G distributor is connected to the instrument.
In the PH201G setup screen, make settings for “Hold contact,” “Fail contact,” and “Wash
contact.”
l Hold contact
SelectDisabledorEnabled.
When this item is enabled, the output will be held according to the setting of “Hold type” on the
Hold setup screen.
l Fail contact
Selectastatusfromamong“Fail+Warn,”“Failonly,”and“Disabled.”
Thissettingdependsontheerrorconguration.See“13.4Errorconguration.”
“Fail” corresponds to “Fault.”
l Wash contact
SelectDisabledorEnabled.
When this item is enabled, items for a wash can be set on the Wash settings screen.
In the Wash settings screen, set the interval time, wash time, and recovery time and setup of
various washes.
Interval time: Set the wash interval in hours.
Wash time/measure time: Set the wash time in minutes. In a continuous wash, wash time is
replaced by measure time.
Recovery time: Set the recovery time in minutes.
Manualwash: Select“Disabled”or“Enabled.”
When this item is enabled, a wash cycle can be activated manually. On the
Calibration/Wash screen, press the “Start manual wash cycle” to perform a
manual wash.
Imp2wash: Select“Disabled”or“Enabled.”
When this item is enabled, a wash cycle can be started if the “Impedance 2
too high” error occurs with respect to the reference electrode.
Continuouswash:Select“Disabled”or“Enabled.”
A continuous wash cycle is started at the instant when this item is enabled.
In a continuous wash, the “Measure time” and “Interval time” are reversed
(see Figure 13.3).
DO
13
- Model FLXA21 1
- 2-Wire Analyzer 1
- CAUTION 3
- CONTENTS 7
- 1. INTRODUCTION AND GENERAL 13
- DESCRIPTION 13
- 2012.01J312FA012 14
- -D-P-S-AA-P1-NN-AN-L1N-NN 14
- /UM/SCT/H6 14
- 4mA 20mAPH1 17
- 4mA 20mADiff-pH 17
- Measurement value (pH) 19
- WARNING 27
- 2. WIRING AND INSTALLATION 28
- 2.1 Installation site 29
- F0202.ai 30
- F0203.ai 30
- F0204.ai 31
- 2.4.1 Grounding 32
- 2.4.3 Wiring cover 33
- 2.5 Sensor wiring 34
- Glass sensor on Input 1 37
- Reference sensor on Input 2 37
- REFTC Liquid 38
- PHTC ORPLiquid 38
- 2.6 Mounting methods 41
- 3. OPERATION OF pH/ORP 43
- 3.1 Change language 44
- 3.2 Quick setup 44
- For details, see section 4.1 45
- Figure 3.5 Change display 47
- Figure 3.6 Detail display 48
- 3.5 Trend graphics 52
- Figure 3.10 Trend screen 53
- Figure 3.11 Trend graphics 53
- 4. COMMISSIONING OF pH/ORP 55
- 4.1 Sensor setup 57
- 4.2 Measurement setup 57
- 4.2.2 Temperature settings 58
- 4.2.4 Calibration settings 59
- 4.2.5 Impedance settings 62
- 4.2.6 Concentration 62
- 4.3 Output setup 63
- Figure 4.4 Redundant system 64
- 4.4 Errorconguration 65
- 4.5 Logbookconguration 67
- 4.6 Advanced setup 67
- 4.6.2 Tag 68
- 4.6.3 Passwords 68
- 4.6.4 Date/Time 68
- 4.6.5 Communication 68
- 4.7 Display setup 71
- Display setup 72
- 4.7.2 Trend 73
- 4.7.3 Auto Return 73
- 4.7.4 Adjust contrast 73
- 4.7.5 MONITOR display 73
- 4.8 Calculated data setup 74
- 5. CALIBRATION OF pH/ORP 75
- 5.1 pH calibration 76
- 5.1.2 Automatic calibration 77
- 5.2 Temperature calibration 79
- Tag:FLXA21–PH 80
- 6.1 Change language 82
- 6.2 Quick setup 82
- 4mA 20mAConduct1-TC1 84
- Figure 6.5 Change Display 85
- Figure 6.6 Detail display 86
- 6.5 Trend graphics 90
- Figure 6.9 Trend screen 91
- Figure 6.10 Trend graphics 91
- 7. COMMISSIONING OF SC 93
- (Conductivity) 93
- Linear 94
- 7.1 Measurement setup 95
- 7.1.5 Calibration settings 97
- 7.1.6 Concentration 97
- 7.2 Output setup 98
- Conduct1 - TC1 : 99
- Conductivity of sensor 1 99
- Temperature compensation 1 99
- Figure 7.2 Redundant system 100
- 7.3 Errorconguration 101
- 7.4 Logbookconguration 102
- 7.5 Advanced setup 103
- 7.5.3 Passwords 104
- 7.5.4 Date/Time 104
- 7.5.5 Communication 104
- 7.5.6 Factory setup 105
- 7.6.2 Trend 106
- 7.6.3 Auto Return 107
- 7.6.4 Adjust contrast 107
- 7.6.5 MONITOR display 107
- Figure 8.1 Calibration 109
- 8.1 Cell constant (manual) 110
- 8.3 Air calibration 110
- 8.4 Sample 111
- 8.5 Temperaturecoefcient 111
- 8.6 Temperature calibration 111
- Tag:FLXA21–SC 112
- Conductivity) 113
- 9.1 Change language 114
- 9.2 Quick setup 114
- Monitor display 115
- Tag:FLXA21–ISC 116
- 9.4 Zooming in on details 117
- Outputsetup→mA 118
- F0310.ai 120
- 9.5 Trend graphics 121
- Figure 9.8 Trend screen 122
- Figure 9.9 Trend graphics 122
- 9.6 Instrument status screen 123
- Parameter Ref. sect 125
- 10.1.1 Measurement 126
- 10.1.2 Conguresensor 126
- 10.1.3 Temperature settings 126
- 10.1.5 Calibration settings 127
- 10.1.6 Concentration 128
- 10.2 Output setup 129
- 10.3 Errorconguration 130
- 10.4 Logbookconguration 131
- 10.5 Advanced setup 132
- 10.5.3 Passwords 133
- 10.5.4 Date/Time 133
- 10.5.5 Communication 133
- 10.6 Display setup 134
- 10.6.3 Auto Return 135
- 10.6.4 Adjust contrast 135
- 10.6.5 MONITOR display 135
- X= 30 mm (Min.) 137
- 11.1 Cell constant (manual) 138
- 11.3 Air calibration 138
- 11.4 Sample 139
- 11.5 Temperaturecoefcient 139
- Execute & Setup 141
- 12.1 Change language 142
- 12.2 Quick setup 142
- 4mA 20mAOxygen1 144
- Figure 12.5 Change display 145
- (Fig.12.7) 146
- (Fig.12.6) 148
- Figure 12.8 Trend screen 149
- Figure 12.9 Trend graphics 150
- Execute &Setup 152
- Commissioning 152
- 13.2 Measurement setup 154
- 13.2.6 Calibration settings 155
- 13.3 Output setup 156
- Reset redundant system 157
- Output setup 157
- 13.4 Errorconguration 158
- 13.5 Logbookconguration 159
- 13.6 Advanced setup 160
- 13.6.3 Passwords 161
- 13.6.4 Date/Time 161
- 13.6.5 Communication 161
- 13.6.6 Factory setup 163
- 13.7.2 Trend 164
- 13.8 Calculated data setup 165
- Figure 14.1 Calibration 166
- 14.1 Air calibration 167
- 14.2 Water calibration 167
- 14.4 Temperature calibration 168
- Tag:FLXA21–DO 169
- Figure 15.1 170
- 15.1 Change language 171
- 15.2 Quick setup 171
- Tag:SENCOM 173
- 15.4 Zooming in on details 174
- F0410.ai 176
- Figure 15.8 Sterilization 179
- (Fig.15.5) 180
- Figure 15.10 Trend screen 181
- Figure 15.11 Trend graphics 182
- 16.1 Sensor setup 186
- 16.2 Measurement setup 187
- 16.2.4 Calibration settings 189
- ORP settings 191
- 16.2.5 Impedance settings 192
- 16.2.6 Concentration 192
- 16.3 Output setup 193
- 16.4 Errorconguration 194
- 16.5 Logbookconguration 195
- 16.6 Advanced setup 196
- 16.6.2 Tag 197
- 16.6.3 Passwords 197
- 16.6.4 Date/Time 197
- 16.6.5 Communication 197
- F050605_2.ai 199
- 16.7 Display setup 200
- 16.7.2 Trend 201
- 16.7.3 Auto Return 201
- 16.7.4 Adjust contrast 201
- 16.7.5 MONITOR display 201
- Figure 17.1 Calibration 202
- 17.1 pH calibration 203
- 17.1.2 Automatic calibration 204
- 17.2 Temperature calibration 206
- 18. MAINTENANCE 208
- 19. TROUBLESHOOTING 209
- Appendix 1 For pH/ORP 213
- Figure 1 Conductivity 218
- 147.6 - 124.5 219
- App.2-10 226
- App.2-11 227
- App.2-12 228
- Appendix 3 229
- App.3-10 238
- App.3-11 239
- ISO 5814:1990(E) 240
- =1atm=760 241
- Customer 242
- Maintenance 242
- Parts List 242
- Revision Record 243
- Supplement 244
- IM 12A01A02-01E 2/3 245
- 5th Edition 245
- IM 12A01A02-01E 3/3 246
Relacionado con productos y manuales para Sensores Yokogawa 2-Wire Dual Channel Transmitter/Analyzer FLXA21
(138 paginas)
(88 paginas)
(88 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales