Yokogawa FVX110 Manual de usuario Pagina 14
- Pagina / 164
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
<2. Handling Cautions>
2-4
IM 01S01C01-01EN
b. FM Intrinsically safe and Nonincendive
Type
FVX110 Fieldbus Segment Indicator with
optional code /FS15.
•
Applicable standard: FM3600, FM3610,
FM3611, FM3810, ANSI/NEMA250,
ISA60079-27
• FM Intrinsically Safe Approval
[Entity Model]
Class I, II & III, Division 1, Groups A, B, C, D,
E, F & G, Temperature Class T4 Ta=60ºC,
Type 4X and Class I, Zone 0, AEx ia IIC,
Temperature Class T4 Ta=60ºC, Type 4X
[FISCO Model]
Class I, II & III, Division 1, Groups A, B, C, D,
E, F & G, Temperature Class T4 Ta=60ºC,
Type 4X and Class I, Zone 0, AEx ia IIC,
Temperature Class T4 Ta=60ºC, Type 4X
• Nonincendive Approval
Class I, Division 2, Groups A, B, C & D
Temperature Class T4 Ta=60ºC, Type 4X
and Class II, Division 2, Groups F & G
Temperature Class T4 Ta=60ºC, Type 4X
and Class I, Zone 2, Group IIC, Temperature
Class T4 Ta=60ºC, Type 4X and Class III,
Division 1, Temperature Class T4 Ta=60ºC,
Type 4X
• Electrical Connection: 1/2 NPT female, M20
female
• Caution for FM Intrinsically safe type.
(Following contents refer to “DOC. No.
IFM040-A11 p.1 to p.6.”)
■ IFM040-A11
● Installation Diagram for Intrinsically safe
(Division 1 Installation)
Non-Hazardous Location
Hazardous Location
F0203.ai
Terminator
Safety Barrier
Field Instruments
Indicator
Field Instruments
+
–
+
–
+
–
Terminator
+
–
+
–
Note 1. Barrier must be installed in an enclosure
that meets the requirements of ANSI/ISA
61010-1.
Note 2. Control equipment connected to the Associ
ated Apparatus must not use or generate
more than 250 Vrms or Vdc.
Note 3. Installation should be in accordance
with ANSI/ISA 12.06.01 “Installation of
Intrinsi cally Safe Systems for Hazardous
(Classied) Locations” and the National
Electrical Code (ANSI/NFPA 70) Sections
504 and 505.
Note 4. The conguration of Associated Apparatus
must be Factory Mutual Research
Approved under FISCO Concept.
Note 5. Associated Apparatus manufacturer’s
installa tion drawing must be followed
when installing this equipment.
Note 6. No revision to drawing without prior
Factory Mutual Research Approval.
Note 7. Terminator must be FM Approved.
Note 8. Note a warning label worded “SUBSTITU
TION OF COMPONENTS MAY IMPAIR
INTRINSIC SAFETY”, and “INSTALL IN
ACCORDANCE DOC.NO.IFM040-A11 P.1
to P.6.”
Electrical Data:
• Rating 1 (Entity)
For Groups A, B, C, D, E, F, and G or Group IIC
Maximum Input Voltage Vmax: 24 V
Maximum Input Current Imax: 250 mA
Maximum Input Power Pmax: 1.2 W
Maximum Internal Capacitance Ci: 1.76 nF
Maximum Internal Inductance Li: 0 mH
or
• Rating 2 (FISCO)
For Groups A, B, C, D, E, F, and G or Group IIC
Maximum Input Voltage Vmax: 17.5 V
Maximum Input Current Imax: 500 mA
Maximum Input Power Pmax: 5.5 W
Maximum Internal Capacitance Ci: 1.76 nF
Maximum Internal Inductance Li: 0 mH
or
• Rating 3 (FISCO)
For Groups C, D, E, F, and G or Group IIB
Maximum Input Voltage Vmax: 17.5 V
Maximum Input Current Imax: 500 mA
Maximum Input Power Pmax: 5.5 W
Maximum Internal Capacitance Ci: 1.76 nF
Maximum Internal Inductance Li: 0 mH
- Fieldbus Segment Indicator 1
- Contents 2
- 1. Introduction 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. Handling Cautions 11
- Protected Instrument 13
- Terminal 15
- 2.8.2 CSA Certication 17
- Location of the mark 22
- 2) Internal grounding 22
- 1) External grounding 22
- 2.8.4 IECEx Certication 23
- 3. Component Names 25
- 4. About Fieldbus 26
- 5. Installation 28
- 5.3 Wiring 29
- 5.4 Grounding 30
- 5.5 Connection of Devices 30
- 5.6 Host Setting 31
- 5.7 Bus Power ON 32
- 6. Conguration 34
- 6.2 Network Denition 35
- 6.3 Denition of Combining 36
- Function Blocks 36
- 6.4 Setting of Tags and 37
- Addresses 37
- 6.5 Communication Setting 37
- 0x1: System/network 38
- 0x1234: Function block 38
- 6.6 Block Setting 39
- 6.6.2 Trend Object 40
- 6.6.3 View Object 40
- <6. Conguration> 41
- 7.3.2 Operating mode 44
- 7.3.1 Function Outline 44
- Quality Sub-status 46
- 7.3.5 Indicator settings 47
- Figure 7.4 Sub Tag settings 48
- (switching displays) 62
- 9. In-Process Operation 64
- 9.3 Device Diagnostic 67
- Simulation Function 67
- 10. Maintenance 69
- Assembly 70
- 11. Device Information 71
- 12. Parameter Lists 74
- 12.2 LCD Transducer Block 77
- 13. General Specications 85
- 13.2 Physical Specications 86
- 13.3 Model and Sufx Codes 86
- 13.5 Optional Specications 88
- 13.6 Dimensions 89
- A1.1 Schematic Diagram of 90
- Signal Characterizer Block 90
- A1.2 Input Section 91
- FA0103.ai 92
- A1.5.1 Input Compensation 95
- A1.5.3 Backward Control 96
- Figure A2.1 Integrator Block 97
- A2.2 Input Process Section 98
- A2.3 Adder 99
- A2.4 Integrator 100
- A2.5 Output Process 101
- IM 01S01C01-01EN 102
- A2.6 Reset 103
- A2.6.2 Reset Timing 104
- A2.6.3 Reset Process 104
- Figure A3.1 IS Block 108
- A3.2 Input Section 110
- A3.2.2 MIN_GOOD Handling 111
- A3.3 Selection 112
- A3.3.2 SELECTION Handling 113
- Figure A3.5 Example (4) 114
- Figure A3.6 Example (5) 115
- Figure A3.7 Example (6) 116
- Figure A3.8 Example (7) 117
- Figure A3.9 Example (8) 118
- A3.4 Output Processing 119
- A3.4.2 OUT Processing 120
- A3.4.3 STATUS_OPTS 121
- FA0311.ai 123
- A4.2 Input Section 125
- A4.2.3 INPUT_OPTS 126
- Inputs and PV 126
- A4.3 ComputationSection 127
- A4.4 OutputSection 127
- AUTO MAN AUTO 128
- BAL_TIME 128
- Appendix 5. PID Block 132
- A5.3 Parameters of PID Block 133
- A5.4 PID Computation Details 136
- A5.5 Control Output 136
- A5.7 Control Action Bypass 137
- A5.8 Feed-forward 137
- A5.9 Block Modes 137
- A5.10 Bumpless Transfer 138
- A5.11 Setpoint Limiters 138
- Fallback (IMan) 139
- A5.15 Manual Fallback 140
- A5.16 Auto Fallback 140
- A5.17 Mode Shedding upon 140
- Computer Failure 140
- A5.18 Alarms 141
- A5.19 Example of Block 141
- Connections 141
- A5.20 View Object for PID 142
- Function Block 142
- (MAO) Block 143
- A6.2 Block Mode 144
- A6.3 Fault State 145
- A6.4 Status Transitions 146
- A6.5 Parameter list display 146
- A7.1 Link Active Scheduler 148
- A7.2 Link Master 148
- A7.3 Transfer of LAS 149
- A7.4 LM Functions 150
- A7.5 LM Parameters 151
- SCHEDULE_LIST_ 152
- CHARACTERISTICS_ 152
- A7.6 FAQs 155
- Field Device 159
- A8.7 Troubleshooting 159
- Software Download 161
- Relating to Software Download 162
- IMPORTANT 162
- (3) DOMAIN_HEADER 163
- Revision Information 164
Relacionado con productos y manuales para Sensores Yokogawa FVX110
(27 paginas)
(60 paginas)
(88 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales