Yokogawa FVX110 Manual de usuario Pagina 146
- Pagina / 164
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
<Appendix 6. Multiple Analog Output (MAO) Block>
A6-4
IM 01S01C01-01EN
A6.4 Status Transitions
Note that inputs IN_1 – IN_8 status are not transferred to LCD Transducer Block as is when the following
settings are made.
Setting Status transition (high-level system priority)
When MAO function block is in O/S mode Bad – Out of Service – No Limit
When fault state to value x = 0 (freeze) (x: 1 to 8) Bad – No comm, with LUV – Const
When fault state to value x = 1 (present) (x: 1 to 8) Bad – No comm, no LUV – Const
When no output is connected to IN_1 – IN_8 Bad – Not Connected – No Limit
The MAO function block CHANNEL is 0
Bad – Conguration Error – <received limit (*)>
(*) received limit: Same as IN_1 – IN_8 status
Something other than the above Same as IN_1 – IN_8 status
A6.5 Parameter list display
Relative
Index
Parameter
Write
Mode
Valid
Range
Initial
Value
View
Description/Remarks
1 2 3 4
0 BLOCK_HEADER Block
Tag
=O/S
Displays Block Tag, DD Revision, Execution Time
and other MAO function block information.
1 ST_REV -------- -------- 2 2 2 2 Describes the revision level of parameters for
setting the MAO function block. The revision
is updated when set values are changed. This
parameter is used to check for parameter changes.
2 TAG_DESC Null A universal parameter intended for storing
comments describing tag data.
3 STRATEGY 0 2 The strategy field is a universal parameter used by
a high-level system to identify function blocks.
4 ALERT_KEY 1-255 0 1 Key information used to identify the location
at which an alert occurred. Generally, this is a
universal parameter used by a high-level system
to identify specific areas in a plant that are under
the control of specific operators to distinguish
necessary alarms only.
5 MODE_BLK 4 4 A universal parameter that represents block
operating condition. It comprises the Actual, Target,
Permit and Normal modes.
6 BLOCK_ERR -------- -------- 2 2 Indicates error status of the MAO function block.
The following bits are used by the MAO function
block.
bit1: Block Conguration Error
bit 4: LO mode
bit 15: O/S mode
7 CHANNEL O/S 1 2 A means for the ore tic ally ac ces sin g LC D
Transducer Block. It cannot be used on the FVX110.
8 IN_1 0 5 5 This is an input (input 1) for the MAO function block.
9 IN_2 0 5 5 This is an input (input 2) for the MAO function block.
- Fieldbus Segment Indicator 1
- Contents 2
- 1. Introduction 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. Handling Cautions 11
- Protected Instrument 13
- Terminal 15
- 2.8.2 CSA Certication 17
- Location of the mark 22
- 2) Internal grounding 22
- 1) External grounding 22
- 2.8.4 IECEx Certication 23
- 3. Component Names 25
- 4. About Fieldbus 26
- 5. Installation 28
- 5.3 Wiring 29
- 5.4 Grounding 30
- 5.5 Connection of Devices 30
- 5.6 Host Setting 31
- 5.7 Bus Power ON 32
- 6. Conguration 34
- 6.2 Network Denition 35
- 6.3 Denition of Combining 36
- Function Blocks 36
- 6.4 Setting of Tags and 37
- Addresses 37
- 6.5 Communication Setting 37
- 0x1: System/network 38
- 0x1234: Function block 38
- 6.6 Block Setting 39
- 6.6.2 Trend Object 40
- 6.6.3 View Object 40
- <6. Conguration> 41
- 7.3.2 Operating mode 44
- 7.3.1 Function Outline 44
- Quality Sub-status 46
- 7.3.5 Indicator settings 47
- Figure 7.4 Sub Tag settings 48
- (switching displays) 62
- 9. In-Process Operation 64
- 9.3 Device Diagnostic 67
- Simulation Function 67
- 10. Maintenance 69
- Assembly 70
- 11. Device Information 71
- 12. Parameter Lists 74
- 12.2 LCD Transducer Block 77
- 13. General Specications 85
- 13.2 Physical Specications 86
- 13.3 Model and Sufx Codes 86
- 13.5 Optional Specications 88
- 13.6 Dimensions 89
- A1.1 Schematic Diagram of 90
- Signal Characterizer Block 90
- A1.2 Input Section 91
- FA0103.ai 92
- A1.5.1 Input Compensation 95
- A1.5.3 Backward Control 96
- Figure A2.1 Integrator Block 97
- A2.2 Input Process Section 98
- A2.3 Adder 99
- A2.4 Integrator 100
- A2.5 Output Process 101
- IM 01S01C01-01EN 102
- A2.6 Reset 103
- A2.6.2 Reset Timing 104
- A2.6.3 Reset Process 104
- Figure A3.1 IS Block 108
- A3.2 Input Section 110
- A3.2.2 MIN_GOOD Handling 111
- A3.3 Selection 112
- A3.3.2 SELECTION Handling 113
- Figure A3.5 Example (4) 114
- Figure A3.6 Example (5) 115
- Figure A3.7 Example (6) 116
- Figure A3.8 Example (7) 117
- Figure A3.9 Example (8) 118
- A3.4 Output Processing 119
- A3.4.2 OUT Processing 120
- A3.4.3 STATUS_OPTS 121
- FA0311.ai 123
- A4.2 Input Section 125
- A4.2.3 INPUT_OPTS 126
- Inputs and PV 126
- A4.3 ComputationSection 127
- A4.4 OutputSection 127
- AUTO MAN AUTO 128
- BAL_TIME 128
- Appendix 5. PID Block 132
- A5.3 Parameters of PID Block 133
- A5.4 PID Computation Details 136
- A5.5 Control Output 136
- A5.7 Control Action Bypass 137
- A5.8 Feed-forward 137
- A5.9 Block Modes 137
- A5.10 Bumpless Transfer 138
- A5.11 Setpoint Limiters 138
- Fallback (IMan) 139
- A5.15 Manual Fallback 140
- A5.16 Auto Fallback 140
- A5.17 Mode Shedding upon 140
- Computer Failure 140
- A5.18 Alarms 141
- A5.19 Example of Block 141
- Connections 141
- A5.20 View Object for PID 142
- Function Block 142
- (MAO) Block 143
- A6.2 Block Mode 144
- A6.3 Fault State 145
- A6.4 Status Transitions 146
- A6.5 Parameter list display 146
- A7.1 Link Active Scheduler 148
- A7.2 Link Master 148
- A7.3 Transfer of LAS 149
- A7.4 LM Functions 150
- A7.5 LM Parameters 151
- SCHEDULE_LIST_ 152
- CHARACTERISTICS_ 152
- A7.6 FAQs 155
- Field Device 159
- A8.7 Troubleshooting 159
- Software Download 161
- Relating to Software Download 162
- IMPORTANT 162
- (3) DOMAIN_HEADER 163
- Revision Information 164
Relacionado con productos y manuales para Sensores Yokogawa FVX110
(27 paginas)
(60 paginas)
(88 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales