Yokogawa FVX110 Manual de usuario Pagina 94
- Pagina / 164
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
<Appendix 1. Signal Characterizer (SC) Block>
A1-5
IM 01S01C01-01EN
A1.4 List of Signal Characterizer Block Parameters
Relative
Index
Parameter
Write
Mode
Valid Range
Initial
Value
View
Description / Remarks
1 2 3 4
0 BLOCK_
HEADER
Block
Tag=O/S
TAG: "SC" Information relating to this function block, such as
block tag, DD revision, and execution time
1 ST_REV - - - - - 2 2 2 2 The revision level of the set parameters associated
with the Signal Characterizer block
2 TAG_DESC Null Stores comments describing tag information.
3 STRATEGY 1 2 The strategy eld can be used by the high-level
system to identify function blocks.
4 ALERT_KEY 1-255 1 1 Key information used to identify the location at which
an alert has occurred
5 MODE_BLK 4 4 Mode of the Signal Characterizer block. O/S, Man,
and Auto are supported.
6 BLOCK_ERR 2 2 Indicates the error status of the Signal Characterizer
block in bit strings.
7 OUT_1 MAN 5 5 Outputs the result of the value of IN_1 corrected
using a line-segment function.
8 OUT_2 MAN 5 5 Outputs the result of the value of IN_2 corrected
using a line-segment function. It is also possible to
approximate the result using the inverse function of
the specied line-segment function. (This is used for
backward control.)
9 X_RANGE 100
0
1342
1
11 The engineering unit of variables corresponding to
the X-axis for display
10 Y_RANGE 100
0
1342
1
11 The engineering unit of variables corresponding to
the Y-axis for display
11 GRANT_DENY 2 The parameter used to check if various operations
have been executed.
The bits in the GRANT parameter corresponding to
various operations are set before being executed.
After the operations are complete, the DENY
parameter is checked for the setting of any bit
relating to the corresponding operation. If no bit
is set, it is evident that the operations have been
executed successfully.
12 IN_1 5 5 Input a signal to be corrected using a line-segment
function.
13 IN_2 5 5 Input a signal to be corrected using a line-segment
function.
14 SWAP_2 0:Initialized
1:No swap
2:Swap
1 Selector switch used to apply the inverse function to
line-segment approximation of IN_2 to OUT_2
15 CURVE_X Curve input points that determine inputs and
outputs.
The "x" points of the curve are dened by an array of
1 to 21 points with a monotone increase.
16 CURVE_Y Curve input points that determine inputs and
outputs.
The "y" points of the curve are dened by an array of
1 to 21 points.
If SWAP_2 is on, the elements of the curve must be
dened with a monotone increase or decrease.
17 UPDATE_EVT Indicates event information if an update event
occurs.
18 BLOCK_ALM Indicates alarm information if a block alarm occurs.
- Fieldbus Segment Indicator 1
- Contents 2
- 1. Introduction 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. Handling Cautions 11
- Protected Instrument 13
- Terminal 15
- 2.8.2 CSA Certication 17
- Location of the mark 22
- 2) Internal grounding 22
- 1) External grounding 22
- 2.8.4 IECEx Certication 23
- 3. Component Names 25
- 4. About Fieldbus 26
- 5. Installation 28
- 5.3 Wiring 29
- 5.4 Grounding 30
- 5.5 Connection of Devices 30
- 5.6 Host Setting 31
- 5.7 Bus Power ON 32
- 6. Conguration 34
- 6.2 Network Denition 35
- 6.3 Denition of Combining 36
- Function Blocks 36
- 6.4 Setting of Tags and 37
- Addresses 37
- 6.5 Communication Setting 37
- 0x1: System/network 38
- 0x1234: Function block 38
- 6.6 Block Setting 39
- 6.6.2 Trend Object 40
- 6.6.3 View Object 40
- <6. Conguration> 41
- 7.3.2 Operating mode 44
- 7.3.1 Function Outline 44
- Quality Sub-status 46
- 7.3.5 Indicator settings 47
- Figure 7.4 Sub Tag settings 48
- (switching displays) 62
- 9. In-Process Operation 64
- 9.3 Device Diagnostic 67
- Simulation Function 67
- 10. Maintenance 69
- Assembly 70
- 11. Device Information 71
- 12. Parameter Lists 74
- 12.2 LCD Transducer Block 77
- 13. General Specications 85
- 13.2 Physical Specications 86
- 13.3 Model and Sufx Codes 86
- 13.5 Optional Specications 88
- 13.6 Dimensions 89
- A1.1 Schematic Diagram of 90
- Signal Characterizer Block 90
- A1.2 Input Section 91
- FA0103.ai 92
- A1.5.1 Input Compensation 95
- A1.5.3 Backward Control 96
- Figure A2.1 Integrator Block 97
- A2.2 Input Process Section 98
- A2.3 Adder 99
- A2.4 Integrator 100
- A2.5 Output Process 101
- IM 01S01C01-01EN 102
- A2.6 Reset 103
- A2.6.2 Reset Timing 104
- A2.6.3 Reset Process 104
- Figure A3.1 IS Block 108
- A3.2 Input Section 110
- A3.2.2 MIN_GOOD Handling 111
- A3.3 Selection 112
- A3.3.2 SELECTION Handling 113
- Figure A3.5 Example (4) 114
- Figure A3.6 Example (5) 115
- Figure A3.7 Example (6) 116
- Figure A3.8 Example (7) 117
- Figure A3.9 Example (8) 118
- A3.4 Output Processing 119
- A3.4.2 OUT Processing 120
- A3.4.3 STATUS_OPTS 121
- FA0311.ai 123
- A4.2 Input Section 125
- A4.2.3 INPUT_OPTS 126
- Inputs and PV 126
- A4.3 ComputationSection 127
- A4.4 OutputSection 127
- AUTO MAN AUTO 128
- BAL_TIME 128
- Appendix 5. PID Block 132
- A5.3 Parameters of PID Block 133
- A5.4 PID Computation Details 136
- A5.5 Control Output 136
- A5.7 Control Action Bypass 137
- A5.8 Feed-forward 137
- A5.9 Block Modes 137
- A5.10 Bumpless Transfer 138
- A5.11 Setpoint Limiters 138
- Fallback (IMan) 139
- A5.15 Manual Fallback 140
- A5.16 Auto Fallback 140
- A5.17 Mode Shedding upon 140
- Computer Failure 140
- A5.18 Alarms 141
- A5.19 Example of Block 141
- Connections 141
- A5.20 View Object for PID 142
- Function Block 142
- (MAO) Block 143
- A6.2 Block Mode 144
- A6.3 Fault State 145
- A6.4 Status Transitions 146
- A6.5 Parameter list display 146
- A7.1 Link Active Scheduler 148
- A7.2 Link Master 148
- A7.3 Transfer of LAS 149
- A7.4 LM Functions 150
- A7.5 LM Parameters 151
- SCHEDULE_LIST_ 152
- CHARACTERISTICS_ 152
- A7.6 FAQs 155
- Field Device 159
- A8.7 Troubleshooting 159
- Software Download 161
- Relating to Software Download 162
- IMPORTANT 162
- (3) DOMAIN_HEADER 163
- Revision Information 164
Relacionado con productos y manuales para Sensores Yokogawa FVX110
(27 paginas)
(60 paginas)
(88 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.194 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales