Yokogawa DAQWORX Manual de usuario Pagina 138
- Pagina / 163
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3-25
IM WX103-01E
1
2
3
4
5
Index
Viewer
Conversion Range and Step
You can specify the range using data numbers or by using cursors. For the method
of specifying the range using cursors, see the procedure in section 3.4, “Statistical
Computation over an Area of Measured/Computed Data.”
By specifying the step, you can save data sampled at certain intervals rather than
converting all the data in the range (when step is set to 1).
Specifying Formats
Select the format for the converted data. When outputting channel data in columns select
Normal, and for rows, select Trans position.
Display Example of the Converted Data (normal)
Display Example of the Converted Data (trans position)
Version
Version
Version
Version
Notes When Converting Data
• There is a limit in the number of data points that Excel and Lotus1-2-3 can handle.
Before executing the conversion, set the channels/groups to be converted, the
conversion range, and the step so that the number of data points is appropriate. If the
limit is exceeded, perform automatic division prior to conversion. Serial numbers are
attached to divided-converted les. In addition, if the free memory space on the PC is
low, you may not be able to load the data using Excel or Lotus 1-2-3.
•
If you set the save destination to a storage medium that has slow access such as a
oppy disk, the saving of the data may take an extended time. It is recommended that
such storage medium not be selected for the save destination.
• Select a save destination with adequate free space.
• The measured data during a burnout or measured data that ex
ceeds the upper/lower
limit of the measurement range are indicated as “+OVER” or “-OVER”
•
If invalid data exists in the converted data (measured value of a channel without input
or computed value when the data used in the equation does not exist), the data is
indicated as “INVALID”
3.7 Converting Data Formats
- MXLOGGER 1
- Trademarks 2
- Revisions 2
- Software License Agreement 3
- Contents 5
- Chapter 3 Viewer 7
- Chapter 4 Calibrator 7
- Chapter 5 Troubleshooting 7
- Functional Overview 8
- Calibrator 10
- 1.2 MXLOGGER Operation Guide 11
- Overview of Operations 12
- Configure the system 13
- For details, see 13
- Click here to hide the Record 14
- Event settings window 18
- • Alarm Monitor 19
- • Trend Monitor 20
- • Numeric Monitor 20
- • Meter Monitor 21
- • All Channel Monitor 21
- Record the data 23
- 1.3 PC System Requirements 27
- Printer and Mouse 28
- Sound Board 28
- Ethernet Port 28
- 1.4 Setting Up MXLOGGER 29
- Configuring the Network 31
- Setting Up the Network 32
- Subnet Mask 34
- Default Gateway 34
- Connected User (User) 34
- Software 34
- 2.2 Configuring the System 35
- Auto Assignment 37
- MX100 Response Check 38
- CF Card Information 39
- Data Acquisition Conditions 40
- Setting the Data File 41
- Automatic Start Function 42
- Record Stop Condition 44
- Mode Is Set to STR) 47
- Setting the Measurement Span 51
- Setting the Scale 51
- Mode Is Set to RRJC (TC)) 51
- Setting the Burnout 52
- Setting the RJC 52
- 2.5 Setting Computations 54
- Importing Expressions 56
- Channels) 59
- Operators 59
- Arithmetic Functions 61
- Time Functions 62
- • Parameter Setting Ranges 62
- • Timer (<timerNo>) 63
- Timer Level Operation 63
- Manual AO Function 63
- Event Functions 64
- Notes on Computation 65
- 2.6 Setting Alarms 67
- Alarm Hysteresis 69
- 2.7 Digital Output 70
- Setting Analog Output 73
- Setting PWM Output 74
- Editing Pattern Output 75
- Deleting Points 76
- Fixed Output 77
- Rectangular Waveform Output 78
- Trapezoidal Waveform Output 78
- Pyramidal Waveform Output 79
- 2.9 Event Processing 82
- Setting Up Data File Events 83
- Setting Communication Events 84
- Setting Start Record Events 85
- Setting Stop Record Events 86
- Setting Up FTP and E-mail 87
- Configuring FTP 88
- Configuring E-Mail 88
- User File Settings 88
- Enabling/Disabling Events 89
- Displaying the Monitor 90
- Click here 93
- Y-Axis Type 98
- Scale Values 98
- Trip Points 100
- Channel Colors 100
- Clipping of Waveforms 100
- Adding Marks 101
- Grid Density 101
- Cursors 102
- Explanation 103
- Starting the Recording 104
- Stopping the Recording 104
- (Project) 106
- Printing Setup Data 107
- Print Preview 107
- Setting Up the Printer 107
- Changing the Port Number 109
- Procedure 111
- Description 112
- Information 113
- 3.1 Loading Data Files 114
- Synchronization 116
- Joining of Divided Files 117
- CF File Joining Function 118
- 3.2 Setting the Display 119
- IM WX103-01E 120
- Y-Axis Values 122
- Showing/Hiding Alarms 126
- Alarm/Mark List Display 127
- Numeric Display 129
- Settings Window 130
- Clearing Cursors 132
- Measured/Computed Data 133
- 3.5 Saving Display Settings 135
- Saving Templates 136
- Using Templates 136
- 3.7 Converting Data Formats 137
- Conversion Range and Step 138
- Specifying Formats 138
- Notes When Converting Data 138
- 3.8 Printing Data 139
- Executing the Print Operation 140
- Print Example 142
- 4.2 Calibration Procedure 147
- Start calibration 151
- 5.1 Troubleshooting 155
- Troubleshooting 157
- Error Messages on the Logger 159
- Error Messages on the Viewer 160
Relacionado con productos y manuales para Software Yokogawa DAQWORX
Software Yokogawa DAQWORX Manual de usuario
(210 paginas)
(210 paginas)
Software Yokogawa DAQWORX Manual de usuario
(17 paginas)
(17 paginas)
Software Yokogawa DAQWORX Manual de usuario
(52 paginas)
(52 paginas)
Software Yokogawa DAQWORX Manual de usuario
(100 paginas)
(100 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.160 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales