Yokogawa DAQWORX Manual de usuario Pagina 156
- Pagina / 163
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-2
IM WX103-01E
The MX100 cannot be detected from the PC or cannot be detected with the Search
button.
Probable Cause Corrective Action Reference Page
The LINK LED does not turn ON.
The cable is broken.
Replace the Ethernet cable. -
The LINK LED does not turn ON.
There is a problem with the hub.
Check the hub’s power supply. If it still does not work, replace the
hub and check the hub’s operation. Also, try to connect the MX100
using the 10-Mbps fixed mode.
-
The LINK LED does not turn ON.
There is a problem with the PC.
Check whether the PC can connect to the network.
Replace the PC’s NIC.
-
The ACT LED does not turn ON.
There is a problem in the connection
between the hub and the MX100.
Check the hub’s power supply. If it still does not work, replace the
hub and check the hub’s operation. Also, try to connect the MX100
using the 10-Mbps fixed mode.
*
The ACT LED does not turn ON.
There is a problem with the PC.
Check whether the PC can connect to the network.
Replace the PC’s NIC.
-
There is a problem in the network
configuration.
The settings are not correct.
Check that the IP address, subnet mask, and default gateway
settings of the PC correspond to the MX100 settings.
2-3, 2-4
There is a problem in the network
configuration.
The setting changes have not taken
effect.
Turn OFF the power to the PC and the MX100, and carry out
reconnection.
-
The PC and the MX100 are not in the
same segment.
Connect the PC and the MX100 in the same network segment.
If the PC and the MX100 are connected as shown in the following
figure, the Search button cannot be used to detect the MX100.
However, you can make a connection manually by specifying the
IP address.
MX
PC
Router
Network A
Network B
2-3, 2-4
* See the MX100 Data Acquisition Unit User’s Manual (IM MX100-01E).
The MX100 is detected by clicking the Search button, but connection cannot be made.
Probable Cause Corrective Action Reference Page
The IP address is set to the default
value.
The default value cannot be used to
make the connection.
Enter the correct IP address. 2-3, 2-4
There is a problem in the network
configuration.
Check that the IP address, subnet mask, and default gateway
settings of the PC and the MX100 settings are correct.
2-3, 2-4
Follow the rules for I/O on the PC
software module style number, and
release number
Check the PC software release number and main unit style
number Upgrade to a later style.
[PC software release no.] ≥ [main unit style no.] ≥ [module style
no.]
*
* See the MX100 User’s Manual (IM MX100-01E).
Six-Channel Four-Wire RTD resistance input module recognized as a 10-CH universal
input module
Probable Cause Corrective Action Reference Page
The MX100 main unit style number
remains at 1.
Upgrade to a later style. **
** See the MX100 Upgrade Kit user’s manual (IM MX100-77).
5.1 Troubleshooting
- MXLOGGER 1
- Trademarks 2
- Revisions 2
- Software License Agreement 3
- Contents 5
- Chapter 3 Viewer 7
- Chapter 4 Calibrator 7
- Chapter 5 Troubleshooting 7
- Functional Overview 8
- Calibrator 10
- 1.2 MXLOGGER Operation Guide 11
- Overview of Operations 12
- Configure the system 13
- For details, see 13
- Click here to hide the Record 14
- Event settings window 18
- • Alarm Monitor 19
- • Trend Monitor 20
- • Numeric Monitor 20
- • Meter Monitor 21
- • All Channel Monitor 21
- Record the data 23
- 1.3 PC System Requirements 27
- Printer and Mouse 28
- Sound Board 28
- Ethernet Port 28
- 1.4 Setting Up MXLOGGER 29
- Configuring the Network 31
- Setting Up the Network 32
- Subnet Mask 34
- Default Gateway 34
- Connected User (User) 34
- Software 34
- 2.2 Configuring the System 35
- Auto Assignment 37
- MX100 Response Check 38
- CF Card Information 39
- Data Acquisition Conditions 40
- Setting the Data File 41
- Automatic Start Function 42
- Record Stop Condition 44
- Mode Is Set to STR) 47
- Setting the Measurement Span 51
- Setting the Scale 51
- Mode Is Set to RRJC (TC)) 51
- Setting the Burnout 52
- Setting the RJC 52
- 2.5 Setting Computations 54
- Importing Expressions 56
- Channels) 59
- Operators 59
- Arithmetic Functions 61
- Time Functions 62
- • Parameter Setting Ranges 62
- • Timer (<timerNo>) 63
- Timer Level Operation 63
- Manual AO Function 63
- Event Functions 64
- Notes on Computation 65
- 2.6 Setting Alarms 67
- Alarm Hysteresis 69
- 2.7 Digital Output 70
- Setting Analog Output 73
- Setting PWM Output 74
- Editing Pattern Output 75
- Deleting Points 76
- Fixed Output 77
- Rectangular Waveform Output 78
- Trapezoidal Waveform Output 78
- Pyramidal Waveform Output 79
- 2.9 Event Processing 82
- Setting Up Data File Events 83
- Setting Communication Events 84
- Setting Start Record Events 85
- Setting Stop Record Events 86
- Setting Up FTP and E-mail 87
- Configuring FTP 88
- Configuring E-Mail 88
- User File Settings 88
- Enabling/Disabling Events 89
- Displaying the Monitor 90
- Click here 93
- Y-Axis Type 98
- Scale Values 98
- Trip Points 100
- Channel Colors 100
- Clipping of Waveforms 100
- Adding Marks 101
- Grid Density 101
- Cursors 102
- Explanation 103
- Starting the Recording 104
- Stopping the Recording 104
- (Project) 106
- Printing Setup Data 107
- Print Preview 107
- Setting Up the Printer 107
- Changing the Port Number 109
- Procedure 111
- Description 112
- Information 113
- 3.1 Loading Data Files 114
- Synchronization 116
- Joining of Divided Files 117
- CF File Joining Function 118
- 3.2 Setting the Display 119
- IM WX103-01E 120
- Y-Axis Values 122
- Showing/Hiding Alarms 126
- Alarm/Mark List Display 127
- Numeric Display 129
- Settings Window 130
- Clearing Cursors 132
- Measured/Computed Data 133
- 3.5 Saving Display Settings 135
- Saving Templates 136
- Using Templates 136
- 3.7 Converting Data Formats 137
- Conversion Range and Step 138
- Specifying Formats 138
- Notes When Converting Data 138
- 3.8 Printing Data 139
- Executing the Print Operation 140
- Print Example 142
- 4.2 Calibration Procedure 147
- Start calibration 151
- 5.1 Troubleshooting 155
- Troubleshooting 157
- Error Messages on the Logger 159
- Error Messages on the Viewer 160
Relacionado con productos y manuales para Software Yokogawa DAQWORX
Software Yokogawa DAQWORX Manual de usuario
(210 paginas)
(210 paginas)
Software Yokogawa DAQWORX Manual de usuario
(17 paginas)
(17 paginas)
Software Yokogawa DAQWORX Manual de usuario
(52 paginas)
(52 paginas)
Software Yokogawa DAQWORX Manual de usuario
(100 paginas)
(100 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales