Yokogawa EJX210B Manual de usuario Pagina 91

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 101
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 90
<11. General Specications>
11-4
IM 01C27C01-01EN
11.2 Model and Sufx Codes
Instruction
The model and sufx codes for EJX210B consist of two parts; a transmitter body section (I) and a ange
mounting section (II). This specication sheet introduces these two parts separately. The transmitter body
section is shown in one table, and the ange mounting section specications are listed according to the
ange size and the process connection style. First select the model and sufx codes of transmitter body
section and then continue on one of the ange mounting section.
F02E.ai
EJX210B
I Transmitter body section
• Flush type (3, 2, or 1 1/2-inch)
• Extended type (4 or 3-inch)
II Flange mounting section
I. Transmitter body section
J · · · · · · · · · ·
No electrical connection, battery-powered type (battery case only; battery cells not
included)
Electrical connection
T01E.ai
Description
Suffix codes
The ‘ marks indicate the most typical selection for each specification.
*1: Order the antenna separately from accessary option.
*2: Remote antenna cables can be attached. Order separately from accessary option.
S · · · · · · · · · · · · · · · · · · ·
0 · · · · · · · · · · · · · · · · · ·
1 · · · · · · · · · · · · · · · · · ·
2 · · · · · · · · · · · · · · · · · ·
3 · · · · · · · · · · · · · · · · · ·
4 · · · · · · · · · · · · · · · · · ·
5 · · · · · · · · · · · · · · · · · ·
J · · · · · · · · · · · · · · · ·
G · · · · · · · · · · · · · · ·
C · · · · · · · · · · · · · · · ·
-9 · · · · · · · · · · · · ·
D · · · · · · · ·
7 · · · · · · · · · · · ·
8 · · · · · · · · · · · ·
9 · · · · · · · · · · · ·
Flange mounted differential pressure transmitter· · · · · · · · · · · · · · · · · · · · · · · · ·
M · · · · · · · · · · · · · · · · · · · · ·
H · · · · · · · · · · · · · · · · · · · · ·
-L · · · · · · · · · · · · · · · · · · · · · · ·
ASTM-B7 carbon steel
316L SST
ASTM grade660 stainless steel
without process connector (Rc 1/4 female on the cover flange)
with Rc 1/4 female process connector
with Rc 1/2 female process connector
with 1/4 NPT female process connector
with 1/2 NPT female process connector
without process connector (1/4 NPT female on the cover flange)
Refer to "Low Pressure Side Wetted Parts Materials" Table below.
Horizontal piping type and left side high pressure
Wireless communication(ISA100.11a protocol)
Cast aluminum alloy with integral antenna
Cast aluminum alloy with detachable antenna (2 dBi)*
2
Cast aluminum alloy without antenna (N connector)*
1
*
2
1 to 100 kPa (4 to 400 inH
2
O)
5 to 500 kPa (20 to 2000 inH
2
O)
Continued on flange mounting section (II)
Digital indicator
N · · · · · ·
Always N
Low pressure side
wetted parts material
Low pressure side
Process connections
Coverflange bolts
and nuts material
Installation
Integral Indicator
Amplifier housing
Model
EJX210B
Measurement
span (Capsule)
Output signal
Flange mounting section
Table. Low Pressure Side Wetted Parts Materials
*1: Cast version of 316 SST. Equivalent to SCS14A.
*2: Hastelloy C-276 or ASTM N10276
The ‘#’ marks indicate the construction materials conform to NACE material recommendations per MR01-75. For the use of 316
SST material, there may be certain limitations for pressure and temperature. Please refer to NACE standards for details.
Capsule
Cover flange and
process connector
Capsule gasket
Low pressure side wetted
parts material code
Drain/Vent plug
Teflon-coated 316L SST 316 SST
Hastelloy C-276
*2
(Diaphragm)
316L SST (Others)
S
#
ASTM CF-8M
*1
EJX210B
Vista de pagina 90
1 2 ... 86 87 88 89 90 91 92 93 94 95 96 ... 100 101

Comentarios a estos manuales

Sin comentarios