Yokogawa ADMAG AXR Manual de usuario descargar pdf (Pagina 85)

<6. PARAMETER DESCRIPTION>

6-37

IM 01E30D01-01EN

IMPORTANT

• Ifthepipeisempty,theoutputuctuatesor

theProcessAlarm(SignalOverow)occurs.

Thepipemustbefullylledwithliquid.

• The instrument checks whether the pipe is

empty or not by measuring the resistance

between the electrode and the ground.

Therefore, it cannot check the status

depending on the conditions in the pipe,

electrode, and noise at the installation sites.

In this case, set this parameter to “No.” Make

sure that the check of the empty status may

failinthecaseofahighviscosityuidor

adhesiveuid.

• It takes 10 to 15 minutes to occur the Empty

Pipe Alarm. The Process Alarm (Signal

Overow)mayoccurduringtheperiodfrom

the empty status to the Empty Pipe Alarm.

NOTE

• When using the empty check function, set

the appropriate parameters based on the

above table. The default setting is “No.”

• Each of the setting values has the following

features. Before using the instrument,

conrmwhathappensintheemptyandfull

status by checking the setting values in the

order:High→Middle→Low.

Example: In the case of High

1) Set the parameter to “High,” empty the pipe,

andconrmthatthealarmoccurs.Duetothe

Empty Pipe Alarm taking 10 to 15 minutes,

theProcessAlarm(SignalOverow)occurs

in this period. If the Empty Pipe Alarm

does not occur in the empty status, the

empty check cannot be carried out. Set the

parameter to “No” in this case.

2) If the alarm is not released after the pipe

isfullylledwithliquid,thesettingvalueis

incorrect. Set the parameter to “Middle” or

“Low” accordingly.

[K20: Empty Status] Display of empty pipe status

hisparameterspeciesthestatusofemptypipe

insidetheowtube.

Setting Status

Normal Filled situation

Empty Unlledsituation

[K21: DC Voltage A] Display of the voltage level at

electrode A

This parameter is used to display the DC voltage

level at electrode A. The possibility of adhesion at

the electrode A is higher when this value becomes

high.

[K22: DC Voltage B] Display of the voltage level at

electrode B

This parameter is used to display the DC voltage

level at electrode B. The possibility of adhesion at

the electrode B is higher when this value becomes

high.

[K23: Empty Level] Setting of the voltage level for

empty pipe detection at the electrodes

This parameter is used to set the voltage level for

empty pipe detection. The parameter would be set

as default value without change for typical use.

This parameter is changed to smaller value when

the Empty Pipe Alarm occurs frequently even if the

lledsituation.

(10) Menu M: Various Adjustment Function

Setting items

Menu M contains items that are relevant to

automatic adjustments.

[M10: Auto Zero Exe] Execution of automatic zero

adjustment function

→ Refer to the description of parameter B50.

[M11: Autozero Time] Setting of execution time for

automatic zero adjustment

This parameter is used to set the execution time of

automatic zero adjustment.

Use the instrument with the default setting “450

seconds”. When the execution time is short, an

error may occur.

[M12: FL Zero(IEL)] Display of the result of

automatic zero adjustment (excitation current (Low))

This parameter is used to display the result of

automatic zero adjustment (excitation current (Low)

at B50(M10): Auto Zero Exe. It is possible to set

arametersascoefcientvaluedirectly.

1 2 ... 80 81 82 83 84 85 86 87 88 89 90 ... 193 194

Comentarios a estos manuales

Sin comentarios

Yokogawa ADMAG AXR Manual de usuario Pagina 85

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Yokogawa ADMAG AXR